X-Rail - System poręczy

5 4 Zink yellow RAL 1018 Panels Posts Graphit black RAL 9011 Technical information Product facts X-Rail Uprights 30x20 mm Horizontals 25x15 mm Posts 50x50 mm Vertical wires Ø 3 mm Horizontal wires Ø 2.5 mm Mesh aperture 50x30 mm Plastic 2 mm (thermoplastic polyester) Sheet 0,8 mm Finish Phosphatising/Epoxy paint Colour mesh panel Graphit black RAL 9011 Colour post Zink yellow RAL 1018 50x50 mm (Other colours can be quoted) To ensure staff safety, fall protection is often needed in various industries. But it may sometimes be hard to know all the regulations and laws that apply to your business. Here is some information on the standards that X-Rail fulfils. Standards met by our fall protection system X-Rail With a combination of panels and posts, handrails, kneerails, and kick plates the X-Rail system prevents accidents and safely protects employees and visitors from risk of falling. According to the regulations, one 10 cm kick plate and a handrail and a kneerail are always required (kneerail is not needed if you install a mesh or other closed panel). Our fall protection is certified to be installed either directly onto concrete floor or bolted to the steel mezzanine I-beams of the mezzanine structure. The system has been fully tested to the standards applicable in the relevant markets. This will give you peace of mind knowing that you can save both time and money and ultimately have a much better solution meeting your requirements. The system has been evaluated by both simulation and actual physical testing. This ensures that the system is fully compliant in all areas it will be installed. DIN EN ISO 14122-3:2016 This part of ISO 14122 contains requirements for non-powered stairs, stepladders and guard-rails which are part of a stationary machinery and of non-powered adjustable parts and movable parts of fixed means of access (like screws, nuts and welding). The ISO 14122 series as a whole is applicable to both stationary and mobile machinery where fixed means of access are necessary. BS 6180:2011 This British standard applicable in the UK provides guidance and the latest recommendations for the construction of barriers in and around buildings. BS 6180 is a standard that will guide the manufacturing company through the process of designing and constructing barriers, including measuring safety, reinforcing structures and testing corrosive or flammable qualities. BS 6180:2011 provides comprehensive benchmarks for the structure, design, height and strength of the barriers, including recommendations about all the materials used. It applies to both temporary and permanent barriers designed to protect people from hazards, restrict access or control vehicle traffic. This standard Standards met by our fall protection system X-Rail describes the requirements for protective, crash and crush barriers as well as those that impose a speed limit of up to 16 km/h. AS 1657:2018 This Australian standard sets the requirements for the design, construction and installation of fixed platforms, walkways, stairways, and ladders that are intended to provide safe access to places used by operating, inspection, maintenance and service personnel. It also applies to movable platforms that are permanently configured, permanently installed roof access, and permanently installed access for inspection and maintenance of the roof itself. The standard also provides information on recommended component dimensions and materials for edge protection. OSHA 1910.29 This American occupational safety and health standard for fall protection systems and falling object protection-criteria and practices ensures that the system meets the comprehensive requirements regarding for example design, heights, installation, materials and strength of the posts, guardrails, anchoring and safety nets. Handrail / Kneerail Available in length to fit panels with the width 1000 mm and 1500 mm. For other widths of panels, the rails needs to be adjusted in length by being cut in place during assembly. Brackets for placement in keyholes are a standard default but if free placement is needed there is a seperated article number. The standard colour is RAL 9011 (only available in this color). Kick plate A kick plate is always included in RAL 9011 (only available in this color). Available in length 1000 mm and 1500 mm, for other lengths the plate needs to be cut in place during assembly. Mesh panels Our mesh panels 1300 mm and 2200 mm comes in 13 different widths. Both of the panels have customized post to fit the height. See next page. The standard panel colour is RAL 9011 but customized colours are available upon request. Sheet metal and plastic panels The X-Rail series also has sheet metal and plastic panels and they come in one height, 2200 mm, and four widths. Sheet metal panels come in standard colour RAL 9011. Post The post 50x50 mm comes in two heights and the colours range is RAL 1018, but customized colours are available upon request. X-Key A unique key for quick panel release. X-Rail panels can only be dismantled using an X-Key (All panel and post orders include one key)